TRA Press Room

NEWS FOR IMMEDIATE RELEASE

Mahr Federal Inc.
Gary Robison
1144 Eddy Street
Providence RI 02905 USA
(401) 784-3275

Media Contact:
THOMAS RANKIN ASSOCIATES
Tom Rankin, APR
401-884-4090
tomr@trankin.com

Click on image to download 300 dpi JPG

Mahr Federal Introduces the MarSurf® LD 130 and LD 260 for Combined Roughness and Contour Measurements

-- Features longest drive, fastest positioning and measuring speed in industry
-- Innovative biomimetic probe arm design with magnetic mounting, automatic probe recognition

PROVIDENCE, RI -- Building on the success of its industry-leading MarSurf® LD 120 system for combined surface and contour measurements, Mahr Federal has introduced a new generation of instruments with a number of improvements and innovations. Together the new LD 130 and 260 feature longer travel--the longest in the industry for the LD 260--the fastest positioning and measuring speeds in the industry, an innovative biomimetic probe arm design with magnetic mounting and automatic probe recognition, dynamic measuring force, extremely low residual noise, and a plethora of other improvements.

"Simply put," said Pat Nugent, Mahr Federal's Vice President of Metrology Systems, "our intent with the design of the LD 130 and 260 was to take the success of the MarSurf LD 120 platform and improve on it in any way we could. "One interesting example is the new probe arm designs, which are biomimetic, meaning their shapes mimic those found in nature. By using these new shapes we've been able to reduce probe weight by as much as 50% while maintaining the same rigidity, and thereby dramatically improving dynamic response."

The MarSurf LD 130 and 260 units feature travel lengths of 130 mm and 260 mm respectively. This not only allows measurement of much larger parts, but with travel speeds up to 200 mm/sec and measuring speeds up to 10 mm/sec (depending on the surface) measuring cycle times can be significantly reduced--as much as 50% in the case of a 260 mm steering shaft with gear tooth measurements at each end.

Improved dynamic response of the probe also helps increase measurement speeds and reduce measurement cycle time by allowing the probe to better track the part surface. In addition, dynamic measurement force allows the drive units to operate at angles of ±45° from horizontal, dramatically increasing the flexibility of the MarSurf LD 130 and 260 systems.

Both units have been redesigned to improve both safety and accessibility. The tip of the newly designed biomimetic probes is now below the lowest point on the housing, allowing improved access in more measuring applications. In addition, while the LD 130 and 260 retain the magnetic breakaway probe feature of the early LD 120 system, the entire lower housings on the new units are pressure sensitive so that in the event of unintended contact with another object an emergency signal is initiated and stops all movement of the drive unit.

Automatic probe recognition has also been improved. While RFID signals used on competing systems can cause confusion if two or more probes are in signal range, Mahr's automatic recognition system is measuring program specific and requires operator confirmation. Thus, the proximity of other probes is not an issue, and should another probe be mounted while an operator is on break, for example, he will be notified before resuming his measurement program.

Finally, the residual noise signal in the new MarSurf LD 130 and LD 260 units has been significantly reduced. This is the roughness "error" that would still be recorded if the probe traced a perfectly flat surface. In the MarSurf LD 120, this was specified at between 34 and 40 nm Rz. In the new units, this has been reduced by nearly 50% to 20 nm Rz. This is a significant improvement for those making ultra-high precision surface and contour measurements.

The MarSurf LD 130 and 260 systems for combined surface and contour measurement are available in a number of different configurations and with a wide range of probe design tips and other accessories.

MFIinfo

Mahr Federal Inc., a member of the Mahr Group, has over 150 years of experience providing dimensional measurement solutions to fit customer application needs. The company manufactures and markets a wide variety of dimensional metrology equipment, from simple and easy-to-use handheld gages to technically advanced measurement systems for form, contour, surface finish and length. Mahr Federal is also well known as a producer of custom-designed gages and a provider of calibration and contract measurement services. Mahr Federal's calibration laboratories are accredited to ISO/IEC 17025:2005 NVLAP Lab Code 200605-0 (see our Scope of Accreditation for accredited calibration processes). For more information visit www.mahrexactly.com

For additional information, contact:
Marketing
Mahr Federal Inc.
1144 Eddy Street
Providence, RI 02905 USA
Tel: (800) 343-2050 or (401) 784-3100
Email: mkt.nafta@mahr.com
Website: www.mahrexactly.com

Photo Caption
<< MarSurf_LD260.jpg >>
The new MarSurf LD 130 and 260 systems for combined surface and contour measurement feature longer travel--the longest in the industry for the LD 260--the fastest positioning and measuring speeds in the industry, an innovative biomimetic probe arm design with magnetic mounting and automatic probe recognition, dynamic measuring force, low residual noise and numerous other improvements.

ref: MFI8661.0912


Return to Main Mahr Federal Page


 

Home | TRA Press Room | Portfolio | Services | TRA Advisor | About TRA | e-mail Us

Thomas Rankin Associates